Peerless Double Sigma Arm Mixer
Thumb

Additional Images

Thumb Thumb Thumb Thumb
Item #:  B109
Manufacturer:  Peerless
Model #:  DA300
Category:  Mixers
Dimension:  2100 lbs
Condition:  Used
Description:

Peerless DA300 Horizontal Mixer

Information from Peerless:
PEERLESS DA300 DOUBLE SIGMA ARM
SERIAL # 84026
CAPACITY: 2100 LBS

Mixer Frame
  • Stainless Steel Exterior
  • Overall Dimensions - 116" long x 72" deep x 96" tall

Mixer Bowl
  • Tilting Bowl
  • Stainless Steel Bowl Sheet
  • Fabricated Bowl Ends
  • Refrigeration - Water/Glycol

Agitator
  • Double Sigma Arm Agitator - Stainless Steel
  • Agitator Spider - Solid Hub
  • Stainless Steel Agitator Shaft
  • Agitator Shaft Seals - Split Clipper

Mixer Canopy
  • Stainless Steel Construction
  • Liquid Inlets - Two (2) Diameter - 2"Type - Bevel Seat
  • Liquid Inlets - One (1) Diameter - 1-1/2"Type - Tri Clamp
  • Flour Gate - 12" square flange, slide gate missing
  • Bowl Seals - Side - Rear

Mixer Drive
  • Double End Differential Drive
  • Motor- 50/25 HP, Two Speed - motor tag missing estimate 50/25 hp
  • 460 Volt, 3 Phase, 60 Hertz
  • Agitator Speed - _40/80 RPM
  • Drive Design uses Chain and Sprockets 80-3, 60T/20T

Mixer Bowl/Door Drive
  • Mechanical Bowl Tilt , Tilt Drive - Spur Gear
  • Tilt Degrees - 90

Operator Interface Panel
  • Stainless Steel Operator Control Panel w/
    Push Button Controls

Electrical Cabinet
  • Remote Electrical Panel Dimensions: 36"W x 60"H
  • Stainless Steel Main Control Panel
  • Remote I/O AB Control Net and Starter Motor Controls AB size 4

REBUILT AS FOLLOWS by BTE, LLC:
  1. Disassembled: Cleaned & Inspected for cracks or excessive wear. Repair or replace where necessary.
  2. Rebuilt gear box with shaft/gear: (1) New Cone Drive Gearbox, (1) New drive Shaft & Pinion, Fit Gear to shaft with new key, Fit shaft to gearbox with new key. Install on mixer.
  3. Stainless Bearing Carriers: New stainless steel material and machine complete (2) new bearing carriers.
  4. Bearings & Seals: Installed all new bearings and seals.
  5. Carrier Support Roller: New Material and machined complete (1) new roller assembly with bronze bushings.
  6. Gears: New (8) gears and assemble with mating components.
  7. Motors: Were inspected and were recently rewound.
  8. Test jacket and repair if necessary and new Stainless Cover over the Jacket
  9. Final Assembly: Reassembled complete with new bearings, gears & seals. Repaired loose condition between (1) lower drive sprocket and shaft. Verified existing lubrication system and lubricated. Deburred & cleaned all sprockets and chains. Installed motors. Tested operation to insure proper
    function.

ELECTRICAL: Electrical and Panel were in good condition so not rebuilt or replaced




Back To List


 
New Turba-Flo Cooling Tunnel

Item: New Turba-Flo Cooling Tunnel

Model: Turba-Flo

Category: Cooling Tunnel

Manufacturer: All Food Equipment

Read more...

image

Item: Woody's Stringer

Model: 40"

Category: Icing

Manufacturer: Woody's

Read more...

image

Item: Mixifier

Model: Mixifier

Category: Mixing

Manufacturer: All Food Equipment

Read more...

image

Item: Pro-Robe Enrober

Model: Pro-Robe

Category: Chocolate Equipment

Manufacturer: All Food Equipment

Read more...